Wireless & IoT
Wi-Fi and the short-range and low-power radios beside it: Bluetooth LE, NFC, Zigbee and Z-Wave meshes, and LoRaWAN's star-of-stars. Asked which link fits a range, battery and topology budget.
on this pageshowhide
explore
- Wi-Fi99 questions
- 802.11 Standards & Bands5 questions
- CSMA/CA & MAC5 questions
- Frame Types & Structure5 questions
- Scanning & Association6 questions
- Roaming & QoS6 questions
- Channel Planning & Surveys6 questions
- Controllers & AP Management6 questions
- WLAN Security60 questions
- Bluetooth12 questions
- Classic vs BLEempty
- Profiles and GATTempty
- Pairing and Bonding6 questions
- Security Modes & Privacy6 questions
- NFC6 questions
- Operating Modesempty
- NDEF Formatempty
- Tag Typesempty
- RF & Physical Layerempty
- Payments & HCEempty
- Relay & Tag Attacks6 questions
- Zigbeeempty
- 802.15.4 PHY and MACempty
- Trust Center & Keysempty
- Z-Waveempty
- Sub-GHz Radio Layerempty
- Command Classesempty
- LoRaWANempty
- LoRa Modulationempty
- Join Proceduresempty
- Device Classesempty
- Adaptive Data Rateempty
- Choosing a Radio Link6 questions
questions
123 · 4 sectionsIn WEP, what do the 24-bit IV and the ICV in each frame do, and why is WEP retired?
basics
~20 sIn WEP each frame's RC4 key is a 24-bit IV, sent in the clear, followed by the shared key, and a CRC-32 ICV is appended. A small IV space repeats and a CRC cannot authenticate, so WEP is retired.
On an 802.11 network, which frame exchanges does a laptop complete between seeing an SSID and sending its first data, and in what order?
basics
~20 sAn 802.11 station finds the network from a beacon or probe response, completes 802.11 authentication (two open-system frames, or SAE on WPA3-Personal), then an association request and response; on a protected network a key handshake follows before user data flows.
In enterprise Wi-Fi, how do autonomous, controller-based and cloud-managed access points differ in where configuration, control and user traffic are handled?
basics
~20 sAn autonomous AP keeps configuration, control and forwarding to itself. A controller-based AP takes its configuration and control decisions from a controller over CAPWAP. A cloud-managed AP is configured from a hosted service but normally controls and forwards locally.
What is an 802.11 beacon frame, what does it carry, and how often does an access point send one?
basics
~20 sA beacon is a broadcast 802.11 management frame an access point sends, by default about ten times a second per BSSID, announcing its SSID, timestamp, capabilities, channel, supported rates, security suites (RSN element) and which dozing stations have buffered traffic (TIM).
In the 2.4 GHz Wi-Fi band, why are access points planned on channels 1, 6 and 11 rather than on any free channel?
basics
~20 s2.4 GHz channel centres sit 5 MHz apart but signals are about 20 MHz wide, so only 1, 6 and 11 clear each other. Partial overlap is worse than sharing a channel: radios cannot decode it and take turns.
In Bluetooth LE, what is the difference between pairing and bonding, and which keys does a bond keep for reconnecting without pairing again?
basics
~20 sPairing is the Security Manager procedure that authenticates the devices and creates keys to encrypt the link; bonding stores those keys so later connections re-encrypt without pairing. A bond keeps the Long Term Key and, if distributed, the Identity Resolving Key.
What do the four levels of Bluetooth LE security mode 1 require, and does a level 4 link satisfy a level 2 requirement?
basics
~20 sLevel 1 is no security; level 2 is encryption after unauthenticated pairing; level 3 is encryption after authenticated pairing; level 4 is authenticated LE Secure Connections pairing with a 128-bit strength key. A higher level also satisfies every lower one.
In LE pairing, how do IO capabilities and the MITM and OOB flags select the association model, and which models resist an active man-in-the-middle?
basics
~20 sOOB data wins when present, neither side requesting MITM gives Just Works, otherwise the IO capability pair decides. Numeric Comparison and Passkey Entry in Secure Connections resist an active interloper, OOB does if its channel does, and Just Works never does.
How does a Bluetooth LE device generate and change a resolvable private address, and who can still recognize it?
basics
~20 sA resolvable private address joins a random 24-bit value to its hash under the device's IRK, and changes on a timer. Only peers given the IRK at bonding can map it back to the identity address.
Which LE association model does a display-less, one-button blood-pressure cuff get when pairing with a phone, and what does it not protect against?
basics
~20 sA device with no display and no numeric input reports NoInputNoOutput, so the pairing selects Just Works. The link gets encrypted, but the key is unauthenticated: Just Works gives no protection against an active man-in-the-middle during pairing.
What does an NFC door reader that accepts only a card's static identifier prove, and what does a card holding a secret key add?
basics
~20 sA static identifier is a value anyone who reads it can present again, so it proves nothing about possession. A card with a secret key answers a fresh reader challenge, which proves it holds the key.
When an NFC card and a door reader complete a keyed challenge-response, why does mutual authentication not stop a relay, and what does?
basics
~10 sRelay forwards a genuine exchange between a far-away card and a reader, so every cryptographic check passes. Only a distance-bounding measure on round-trip time, or a user-presence step, addresses it.
How does NIST SP 800-98 separate a contactless card's nominal operating range from its eavesdropping and skimming ranges?
basics
~10 sThe nominal operating range is where authorized transactions are expected; eavesdropping, rogue skimming and rogue command ranges are separate distances for other parties. Data-sheet centimetres describe the first, not the others.
NFC poster tags on campus open an unexpected website: how should a reader app treat a tag's URI, and what does Android do itself?
basics
~20 sTreat a tag's URI as untrusted input: show where it leads, ask before opening, and accept only expected schemes and hosts. Android 17 adds an open-link notification for web-link tags that needs explicit user interaction.
An Android app emulates an access card with host-based card emulation: what does requireDeviceUnlock control, and what does user presence leave open?
basics
~20 sSetting android:requireDeviceUnlock to true makes Android require the device to be unlocked before the card-emulation service handles reader commands. It ties a tap to the holder, but does not prove the phone is near the reader.
For battery temperature sensors on every floor of an office building, why is ordinary Wi-Fi usually the wrong radio, and which links fit better?
basics
~20 sA coin-cell sensor sending a few bytes a minute needs a radio that sleeps almost always; classic Wi-Fi spends energy on rates it never uses. Bluetooth LE, Zigbee, Thread or Z-Wave fit, reaching IP via a hub, gateway or border router.
For lighting control in a twelve-storey office, how do mesh links such as Zigbee and Thread differ from star links, and where does sub-GHz help?
basics
~20 sIn a mesh (Zigbee, Thread, Z-Wave) powered nodes relay for each other, so coverage grows with the devices; in a star (Wi-Fi, Bluetooth LE, LoRaWAN) each device reaches a hub directly. Sub-GHz radios trade rate for reach through walls.
For parking-bay sensors 800 m from an office building, how do LoRaWAN, NB-IoT and Wi-Fi HaLow compare in spectrum, duty cycle, data rate and latency?
basics
~20 sLoRaWAN uses unlicensed ISM bands, some duty-cycle limited, at 0.3-50 kbit/s on EU 868 MHz, on your own or a public network. NB-IoT uses an operator's licensed spectrum without duty-cycle limits. HaLow gives native IP at about 1 km.
In a smart-building design, how does each radio reach the IP network: natively over Wi-Fi, through a Thread border router, or through a Zigbee, Z-Wave or LoRaWAN gateway?
basics
~20 sWi-Fi and HaLow devices run IP natively. Thread and IPv6 over Bluetooth LE carry compressed IPv6 (6LoWPAN) to a border router that routes it. Zigbee and Z-Wave need a translating hub; LoRaWAN gateways forward radio frames to a network server.
Leading a smart-building rollout, would you standardise one radio across the site or choose a link per device class, and run your own network or buy an operator's?
basics
~20 sUsually neither extreme: a small set of standards, one per device class, such as Wi-Fi for high-rate devices, one low-power mesh indoors, one long-range link outside. Own the network where you need control; buy an operator's where coverage matters.